John Green shares a fast-track solution for installing floorcoverings as part of
a refurbishment after flood damage.

USING a real-life example of where
F Ball’s technical service department has provided advice on the best course of action for a particular flooring installation, I’ll share a fast-track solution for installing floorcoverings as part of a refurbishment after flood damage.

Flooring contractors often face pressures to complete flooring installations in a short amount of time. Added to this, when installing floorcoverings as part of a refurbishment they will frequently encounter a number of challenges that they would be less likely to find in new-build settings, including dealing with damaged or contaminated subfloors.

This was the case when one of our tech reps was called to a school where the roofs of two school halls had blown off during a storm. Consequently, they were flooded and the floors needed replacing. Once the roofs had been repaired, a solution was required to refurbish the floors as quickly as possible, so the facilities could be returned to use.

Initial inspection
In this case, the floorcoverings in both school halls were wood, so they had begun to warp and were completely ruined. In one there were wooden blocks, installed in a herringbone pattern; in the other there was a wooden sprung sports floor.

When the floorcoverings were removed, it was evident the sand/cement screeds underneath weren’t in a good shape. Rather than being strong and compact, they were crumbling and yellow. When some of the wood blocks were lifted, parts of the floor came with them. The screeds were probably past their natural life span, but undoubtably the moisture had worsened the problem. Unfortunately, this meant they’d need replacing before new floorcoverings could be installed.

Time-saving solutions
To catch up on lost time, pump-applied concrete flowing screeds, which cure overnight, were installed to quickly replace the damaged base.

Normally, you’d have to wait weeks for a newly installed concrete screed to dry sufficiently to be able to install floorcoverings without risking floor failure. Where subfloor relative humidity (RH) levels exceed 75% (or 65% where wood floorcoverings will be installed), there is the potential for subfloor moisture to attack floorcoverings and adhesives, which can result in complete floor failure.

However, as a fast-track solution was required, instead of waiting for the subfloor to dry naturally, our tech rep recommended that F Ball’s Stopgap F78 waterproof surface membrane was applied to prevent excess subfloor moisture damaging floorcoverings.

The solvent-free, one-component, ready-to-use system is applied in two coats to create a barrier against RH levels of up to 95%. The first coat only requires 15-20 minutes curing time; while the second requires a further 30 minutes to cure, meaning a barrier against residual construction moisture and rising damp can be created in less than two hours.

Heavy-duty base
When using Stopgap F78, you don’t need to prime the surface prior to the application of other subfloor preparation products, so flooring contractors could proceed straight to applying a suitable levelling compound to create a perfectly smooth base for the receipt of new floorcoverings once the waterproof surface membrane had cured.

F Ball’s Stopgap 300 HD was chosen for its high compressive strength, meaning that floors will be able to withstand the high levels of wear the school halls were expected to be subject to.

Helpfully, the levelling compound can also be pump-applied up to 1,500sq m per day, dependent on manpower, thickness applied and equipment used, saving further time.

Final thoughts
Once the levelling compound had cured, flooring contractors were able to install new, wood-effect, cushioned vinyl sheet floorcoverings using an adhesive listed as compatible in our Recommended Adhesives Guide (RAG).

F Ball’s Styccobond F46 pressure sensitive adhesive was selected for its strong initial tack, which is useful for holding floorcoverings in place when working with both vinyl sheet and tiles.

Published yearly, the RAG details the compatibility of F Ball adhesives with over 6,000 floorcoverings produced by over 200 manufacturers. A continuously updated version is available on the F Ball website and as a free app.

Thanks to fast-track products, we were able to resolve a challenging situation quickly.
www.f-ball.co.uk
John Green is from F Ball and Co’s technical service department